![]() “The main thing to check is that it’s definitely compatible with the first iPad’s LCD screen which has the model number LP097X02,” Chris says. Once he’d isolated the screen, it was then a case of hooking it up to a Raspberry Pi Zero W. As my glass was already cracked, I went with a much more brute force approach.” “In theory, you should just be able to pop the glass out from the metal frame, and using a thin metal spudger seems to be the way to go. ![]() “It’s a lot easier if the glass is not already cracked,” he explains. Unfortunately, this was the most difficult part of the build. “I knew, from watching a few videos on iPad repairs, that the LCD screen was completely separate from the glass, so it seemed a shame to throw the whole thing away without at least trying to salvage some components,” he says. The project entailed removing and using the iPad’s screen. What’s more, since he’d already written a magic mirror web page and server, the switch proved relatively easy. By swapping it for an iPad, however, he was able to liberate the Amazon-made Fire device for day-to-day use. “The glass was also cracked and the batteries didn’t charge, so it was heading to the bin.” Or at least it was until Chris decided to use it as the basis for a magic mirror.Ĭhris had explored such a project before, using a Fire tablet for the display. Once everything is in place, install the magic mirror software and configure it to your liking.“My iPad was so old that apps didn’t really work any more and the Safari browser wasn’t performing well with modern websites,” he says. I also installed a camera for facial recognition, a microphone to receive voice commands, a motion sensor to save power and speakers for an audio output from the mirror. The power goes to the monitor and to the power adapter for the raspberry pi module. ![]() I drilled mine at a location which will be closest to the power outlet after I hang the mirror. I put some furring strips around the border to ensure that the monitor is level and wont drop out of the frame.ĭrill a hole on the side to route the AC power to the mirror. Measure and cut a piece of black foam board to cover the area of the frame outside the monitor. I will probably select a different vendor if I were to do it again or may be make my own. I went for a 3mm prebuilt 2-way mirror but it had a slight fun house mirror effect. There is also an option to build one from scratch with acrylic or glass and a reflective window tint. This will prevent any damage to the special coating during the normal cleaning and daily use of the mirror. Take a moment to identify the side with the coating and keep it facing towards the back side of the magic mirror. But when the light is bright on one side, and much darker on the other, the glass will look like a mirror to the people on the brighter side. If the light intensity is the same on both sides of the glass, the mirror will look like a normal piece of glass. This means it reflects about half the light that hits its surface and allows the other half to pass through to the other side. ![]() However, while the reflecting coating on regular mirrors is dense and returns all the light that strikes its surface, the reflective coating on two-way mirrors is more sparse. Like all mirrors, these mirrors have a reflective coating. Install a 2-way mirrorĪ bit about the 2 way mirrors. So, I covered it up with some black tape to avoid possible light reflection. Remove the plastic frame around the monitor to expose the bare screen and the electronics. Drill some holes on the top and bottom sides of the frame for ventilation. Once dry, it is ready for sanding and color. Secure the front of the frame to the sides using some wood glue and let it dry for a couple of hours. I used some inexpensive 2 1/2" furring strips. Create the electronics housingĪssemble the sides of the frame. The dimensions were based on the space available on the wall, the size of the computer screen I had, and the cost of the 2-way mirror I had the budget for. So, I used some door trims that were left over after I had replaced the slab doors with the 6 panel doors in my house. ![]() I wanted to give it a slightly antique look to strike a contrast with the relatively modern concept of a smart mirror. Construct a frameĬonstruct a decorative frame to match your style. I recently created a magic mirror to spend more time on front of the screen (as if my current screen consumption is not enough :)Ī brief overview of the steps I followed is given below: 1. The technology is driven by a Raspberry Pi or PC, combined with voice recognition and touch technology. The magic is created by placing a transparent mirror over a tablet, monitor, or TV. A Magic Mirror, also known as a smart mirror, displays the time, weather, calendar, news, and social media updates. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |